Time limit is exhausted. Please reload CAPTCHA. 7 + six =
CANTY specializes in Mud Flow Analysis as well as Drilling Mud PSA.
Name
Email address
Phone
Inquiry
Features:
• Lab Particle size down to 1µm
• Analysis of oil or water based mud
• Detect oil / water / solids / gas
The CANTY SolidSizer™ is a vision-based sensor used with the CANTY Vector System image processor for dry sand size measurement in a laboratory environment. The CantyVision™ Software accurately measures multiple aspects of the sand from area / perimeter / minor and major axis / etc. In comparison to a sieve which measures only minor axis the CantyVision™ software can correlate directly to a sieve so the customer does not have to change any QC documents. The SolidSizer™ can correlate within 2% of a sieve. A typical sieve analysis takes anywhere from 20-30 minutes including cleaning and setup for a 70-100 gram sample. On the SolidSizer™ that same sample takes less than 2 minutes. Also multiple screen distributions can be setup to accommodate multiple customers or areas in the process, hence eliminating the need for multiple runs on the same sand for different size distributions. After correlating to current methods of minor axis, customers find benefit in comparing minor axis to major axis and making sure the sand is round instead of needle shaped. Reduce lab time and make sure production samples are not skipped over due to lack of sample time available!
• Volume Flow Analysis
• Fluid Front Detection
• Real-Time Viewing
• Inline Particle size down to 1µm
Cracking furnaces are used in a variety of applications such as the production of ethylene, hydrogen, vinyl chloride monomer (VCM), and ammonia. In each of these processes, it is important to measure the the temperatures of the tubes in which the reaction is occurring. This measurement is widely known as tube metal temperatures (TMT’s). CANTY’s high temperature camera systems are installed on these furnaces to obtain video during operation. This video is fed into CANTY’s Smart Tube software to monitor TMT’s, identify hot spots, and even track the position of individual tubes as they shift over time.
The CANTY Inflow™ is a vision-based camera system used with the CANTY Vector System image processor for water in hydrocarbons and particles in hydrocarbons in a lab environment / at-line / in-line process. The presence of these two physical contaminants is a problem for equipment the hydrocarbon is going into. The CantyVision™ Software accurately measures multiple aspects of the hydrocarbons from water / solids / gas independent of each other for accurate data. In comparison to a laser and capacitance, which measures only one dimension and can’t identify the difference of water and solids in the stream. The CantyVision™ software can identify the differences. The customer can also visually verify the readings. Hydrocarbon contamination takes place mainly in production and transportation. CANTY objectively takes the measurement and reports based on a two dimensional image. Solids & water are all measured and continuously and objectively monitored. By knowing whether there is a water or solids problem this helps the operators identify how to fix the problem. The Inflow™ is an in-line analysis system to make sure production samples are not skipped over!
CANTY specializes in WATER IN OIL monitoring. CANTY can detecting the water droplet size as well as concentration independent of solids or gas.
The SHORT LOOP SAMPLER™ Oil In Water Analyzer / Water In Oil Analyzer combining sampling point and the INFLOW™ Process Particle Analyzer, provides real time concentration and particle size analysis. The SHORT LOOP SAMPLER™ allows operators and skid manufacturers to test multiple point in their line using only one analyzer and verify the results by using the sample point to verify reading in the lab. Models measure 0.7 micron – 20,000 micron particles under process conditions. By continuously measuring the product OIL, WATER, SAND, and GAS the OiW / WiO concentration and size is output 30 frames a second. This allows the user to see the impact of any change to the refining or drilling system. By using a vision based system CANTY can easily detect all phases and separate them to give PPM/PPB distribution as well as SIZE distribution of all particulates. The system is designed to continuously sample from the center of the process stream and input the entire sample back into the stream so there is no loss of product when analyzing for concentration or particle size.
Min Fluid Velocity: 3 ft/s (If lower consult factory)
Max Fluid Velocity: 15 ft/s